Please Visit Our Forum
 
HomeHome  GalleryGallery  FAQFAQ  SearchSearch  MemberlistMemberlist  RegisterRegister  Log inLog in  
Latest topics
» What happened ?
Mon 19 Dec 2011, 8:47 am by Kraze

» KooNModZ Jtag Shop *UPDATED*
Mon 19 Dec 2011, 8:37 am by Kraze

» Things to know about home solar energy systems.
Mon 27 Jun 2011, 4:35 am by ChaseEvelyn

» MUST READ!
Fri 17 Jun 2011, 1:57 pm by Kraze

» [Release] Wallhack, Mod menu XP, UAV, Superjump, Nuke infect
Wed 18 May 2011, 1:01 pm by SpeedModz

» Do we have ranks like the TTG?
Tue 19 Apr 2011, 12:53 pm by SpeedModz

» SPEED READ THIS
Tue 19 Apr 2011, 9:16 am by Speed_JeLLo

» Linux and not Mac Ubuntu Help PLEASE
Mon 18 Apr 2011, 12:19 pm by SpeedModz

» we got 100 users
Mon 18 Apr 2011, 12:10 pm by SpeedModz

Top posters
-MOD- (271)
 
Speed_JeLLo (250)
 
SpeedModz (144)
 
Speed (118)
 
MoNsTaMaSh (45)
 
Sexy (19)
 
Kraze (12)
 
PureVVater (6)
 
*TrOniiCsx3D* (5)
 
-Penguin- (5)
 
Who is online?
In total there is 1 user online :: 0 Registered, 0 Hidden and 1 Guest

None

Most users ever online was 16 on Fri 20 May 2011, 3:17 pm
Statistics
We have 176 registered users
The newest registered user is chryjayci

Our users have posted a total of 899 messages in 219 subjects
Log in
Username:
Password:
Log in automatically: 
:: I forgot my password
Search
 
 

Display results as :
 
Rechercher Advanced Search

Share | 
 

 How To Mod Your Controller

View previous topic View next topic Go down 
AuthorMessage
Speed_JeLLo
Resident Elite
Resident Elite
avatar

Posts : 250
Points : 10123989
Reputation : -21
Join date : 2011-04-05

PostSubject: How To Mod Your Controller   Sun 10 Apr 2011, 5:11 pm

THIS IS HOW TO MOD YOU CONTROLLER


This is how to add mods to your xbox controller? Playing Xbox is amazing.There is lots of different things to do.The best thing to have in your hand is a modded controller.So enjoy my tut XMB





To mod an Xbox 360 controller you will need the following:
Tweezers
Resistor
30 AWG electric wire
Colored surface mount LED's
Hot glue
Solder
Pliers
Portable drill
Utility knife
Wire cutter
Wire stripper
Hot glue gun
Soldering iron
Philips jeweler's screwdriver
Newspaper




STEP ONE.Put newspaper out on the table. Place controller face down on the newspaper. Take the screws out of the back with your Philips jeweler's screwdriver. Scratch off serial sticker using the screwdriver, then take the screw from beneath the sticker. Take the bottom part of your controller and put it inside.




STEP TWO.Take controller apart. You will need to remove each part of the controller. The buttons, the rubber contact pads, the thumb stick, the D-Pad and the front as well as back inserts from the controller. Make sure all parts of the controller are placed somewhere like a cup so that none of the small pieces are lost.




STEP THREE.
Heat up your soldering iron. Touch the tip of the soldering iron with each of the four LEDs that surrounds the circuit board near their contact points. Take out the LEDs with tweezers. Put the four colored LEDs inside the circuit board and replace the four that were removed. Use the solder on each of the contacts and let the solder cool




STEP FOUR.Remove the Xbox 360 dome button from your controller. Remove the status ring and the guide button out of your dome button. Place the dome button down on the newspaper with the open end facing up. Insert some hot glue into the dome button. Place three colored LEDs into the hot glue where the contact legs stick up and let the glue set.




STEP FIVE.Connect the LEDs pin. You will need to start with one LED then bend the negative contact pin toward the positive contact pin of the LED beside it. You will repeat this step until all of the pins except the first one's positive pin and the last one's negative pin has been bent toward one another. Solder all of the pins to hold them in position.




STEP SIX.Cut two pieces of six inch long electric wire. You can use the wire cutters to cut the electric wire. You will need to strip the insulation off of both ends of your wire strippers. Solder the end of one wire of the positive contact from the LED that has not been bent. You then need to solder one end of the other wire from the negative contact from the other LED that has not been bent. Put the status ring and the guide button back into your Xbox 360 dome button and put the dome button back in the shell of the controller.





STEP SEVEN.Grab and flip the circuit board over. Solder one end of the resistor of the positive contact near the USB cable that is attached to the circuit board. You will then solder the free end of the positive wire of the other contact on the resistor. Solder the free end of your negative contact at which the USB cable attaches to the circuit board. From here you can attach all the the buttons and pieces of the Xbox controller together and enjoy your new modded controller XMB hope you engoyed thanks.[/size]

_________________
Back to top Go down
View user profile
 
How To Mod Your Controller
View previous topic View next topic Back to top 
Page 1 of 1
 Similar topics
-
» Pro Controller
» Controller - Dead zone setup for circuit racing
» modded controller
» Using a controller to play Crusade
» MLG Controller

Permissions in this forum:You cannot reply to topics in this forum
SpeedModZ :: General Discussion :: General Discussion-
Jump to: